Animated graphic possibly with cut aways

Анульовано Опубліковано %project.relative_time Оплачується при отриманні
Анульовано Оплачується при отриманні

I need a visual depiction of the following:

Oil Extraction Interface

This solution consist one or two electromagnetic safety locking extraction hatches. The locking mechanisms are large metal steaks in sliding corridors. The corridors are 4 (four) to 6 (six) inches in width and the length depends on the size and scope of the well requirement. This is part of the well cap that sits atop the blowout preventer or replaces it.

The extraction hatches open by the asserting of an electrical charge to the electromagnet. Once the electromagnets have been activated the sliding steaks will be withdrawn. The air sealed outer shell then allows two interface covers to be drawn outward and slid down two containment tracts.

Once the inner shell is exposed an air sealed unidirectional valve will allow for the insertion of the riser extractor.

Between the inner and outer shell of the well cap resides the housing for the air sealed power, sensor, and indicator cable runs. Though the cables will be water proof and all connections will be sealed, this area of the containment cap should have all air removed so as to create a vacuum and be sealed or filled with water resistant materials.

The inner shell can be composed of a heavy duty plastic or stainless steel. The outer shell should be composed of steel and coated with a water resistant material. (Except for the guide posts which guides the riser pipe connection into proper connection position.)

The two guide post guide the riser pipe receptacle into correct position to interface. At the base and between the two guide posts is the power connection. This power connection is either water resistant or in an air sealed configuration that allows the provision of power to the electromagnets. If for any reason the power is cut, all connections release and the well will be capped automatically.

At each point of the connection an indicator light will show proper connection. Should at any time a catastrophic disaster occur the connection would instantaneously be severed and the well capped.

Riser Pipe and connection

The riser pipe is not permanently affixed to the well. The riser pipe is affixed to the oil rig / mobile oil rig. The oil rig / mobile oil rig (oil rig) supplies power to the entire unit. Should there be a power failure to the oil rig a quick disconnect takes place between the well cap oil extraction interface and the riser oil extraction interface.

The riser can / may be retractable allowing for mobility of the oil rig.

Connection to Well

An interfacing pipe extends from the well cap. The pipe is also equipped with an oversized high-pressure clamp which affixes the well interfacing pipe to the well, unless directly welded or affixed to the pipe. The high pressure clamp is connected to a motorized pulley. The pulley serves as the locking system for the oversized high-pressure clamp. Each locking mechanism of the clamp are linked to high tension corrosion resistant cable. This cable feeds through strategically placed bored holes or welded loops on the clamp and fed directly into the pulley which when activated lock the clamp. The clamp is also chained or attached to each segment of pipe with built in hooking mechanisms by high density non corrosive cable or chain link.

Pulley / Wench system

The pulley / wench system is a high power electric or hydraulic pulley /wench system housed in a plastic dome. Also housed in the dome, is a camera, electrical interface, and air tube.

Brief description of how the solution is different from anything that currently exists in this configuration.

There currently is nothing to compare this invention to.

This invention allows for a self sealing cap on oil wells drilled in the future and/or can be retrofitted to currently existing wells.

This will revolutionize the way we extract oil from deep sea wells. It will also provide a level of safety and security that has never been experienced in the past.

Description of Invention

The self sealing well cap can only be activated by the activation of the electrical interface of the riser pipe. If there is no flow of electricity, the cap will not open and access to the oil will not be allowed. If at any time the flow of electricity is halted, a quick disconnection will take place between the self sealing well cap extraction interface and the riser pipe extraction interface.

Adobe Flash Анімація AutoCAD CAD/CAM Ілюстратор

ID Проекту: #697943

Про проект

10 заявок(-ки) Дистанційний проект Остання активність Jun 7, 2010

10 фрілансерів(-и) готові виконати цю роботу у середньому за $463

salmanaim

Hi, Animations here we go. Lets do it Together. Please see Pm SK

$450 USD за 15 дні(-в)
(214 відгуків(и))
8.2
sgdesignstudio

Flash Animator @ your service.

$750 USD за 12 дні(-в)
(172 відгуків(и))
6.7
blend4design

Please see PM for details, thanks

$375 USD за 3 дні(-в)
(26 відгуків(и))
5.5
JMAIER

USA engineering designer with experience designing systems for Michelin, BMW, and other companies both small and large; I am an expert in Solidworks engineering software and teach a Solidworks course at a local Univers Більше

$400 USD за 3 дні(-в)
(0 відгуків(и))
0.0
ShaneSmith

Hello please see PMB for details and my quote.

$600 USD за 14 дні(-в)
(0 відгуків(и))
0.0
soldencompany

we are professionals and complete the job on time

$250 USD за 2 дні(-в)
(0 відгуків(и))
0.0
sudhirsadangi123

work time perfection

$300 USD за 3 дні(-в)
(0 відгуків(и))
0.0
rgespino

High quality control and delivering the job on time.

$750 USD за 10 дні(-в)
(0 відгуків(и))
0.0
nabeelca

Dear Sir....Plz check your PM box for details...Thank You..This bid is based on 95% accuracy.

$450 USD за 5 дні(-в)
(0 відгуків(и))
0.0