Find Jobs
Hire Freelancers

Design of 5V PWM to 0-10VDC analog output circuit to drive VFD

₹600-1500 INR

Закрито
Опублікований over 8 years ago

₹600-1500 INR

Оплачується при отриманні
We are using ATMEGA2560 and already using some circuit to convert 5V PWM to 0-10VDC analog output circuit. It works fine on no load and no normal environment. If we use this circuit to drive VFD in a industrial noise environment, then there is voltage drop on the analog output. The 10V drops to 7V. We need a reliable circuit to convert 5V PWM to 0-10VDC analog output circuit to drive VFD in a industrial environment.
ID проекту: 8848965

Про проект

14 пропозицій(-ї)
Дистанційний проект
Активність 8 yrs ago

Хочете заробити?

Переваги подання заявок на Freelancer

Вкажіть свій бюджет та терміни
Отримайте гроші за свою роботу
Опишіть свою пропозицію
Реєстрація та подання заявок у проекти є безкоштовними
14 freelancers are bidding on average ₹1 526 INR for this job
Аватарка користувача
A proposal has not yet been provided
₹1 300 INR за 1 день
4,7 (6 відгуки(-ів))
2,4
2,4
Аватарка користувача
it can be solved by implementing some filtering and feed back. Are you using arduino ATMEGA2560 ? What is the distance between ATMEGA2560 board and VFD? Regards Tahir
₹3 333 INR за 5 дні(-в)
5,0 (3 відгуки(-ів))
2,1
2,1
Аватарка користувача
Hello, I'm interested in your project, I have some questions: Could you upload the circuit you are using? Is there available any figure of the input impedance of the VFD? What happen if you test the circuit with the VFD in a non-industrial environment? I look forward to your reply. Thank you.
₹1 750 INR за 6 дні(-в)
5,0 (3 відгуки(-ів))
2,0
2,0
Аватарка користувача
A proposal has not yet been provided
₹1 300 INR за 1 день
5,0 (1 відгук)
1,6
1,6
Аватарка користувача
Hi, I'm a responsible person who is serious in work.I also have work experience in electronic engineering
₹850 INR за 2 дні(-в)
0,0 (0 відгуки(-ів))
0,0
0,0
Аватарка користувача
Hello Sir, am ready to work on what are you asking am a micro electronics engineer and have support of some experts engineers in my area. i will be happy to help you once you give me more details Best regards, Chris
₹1 300 INR за 3 дні(-в)
0,0 (0 відгуки(-ів))
0,0
0,0
Аватарка користувача
I am able to only provide you schematic and you need to test by your self because i am not available in india now. and I have not any setup with me. I am embedded Firmware Developer.
₹3 333 INR за 3 дні(-в)
0,0 (0 відгуки(-ів))
0,0
0,0
Аватарка користувача
A proposal has not yet been provided
₹1 250 INR за 1 день
0,0 (0 відгуки(-ів))
0,0
0,0
Аватарка користувача
Your problem seems to be quite common. But we will need more information about the real environment and the power source(s) of your board.
₹1 500 INR за 3 дні(-в)
0,0 (0 відгуки(-ів))
0,0
0,0
Аватарка користувача
Prefect circuit i will give you
₹1 250 INR за 5 дні(-в)
0,0 (0 відгуки(-ів))
0,0
0,0
Аватарка користувача
Dear Employer, I have already done a project like this. I have designed and implemented a controlling system for industrially used transformer winding machine (see my portfolio) and it works properly. It has a 3-phase motor and an inverter (Fuji FVR-G7S-EX) to drive the motor. The inverter has an analog input to control the speed, normally it uses a potentiometer to vary the speed manually. I have designed a circuit convert digital PWM signal to the analog voltage to vary speed by the MCU. It also uses 0V to 10V. My circuit capable to driving motor lowest speed (0.6Hz) on zero duty cycle and highest speed (60Hz) on 255 duty cycle. I have used small no. of components available in a market. I have used MOSFET to get the maximum range of motor speed. I have used Opto-Coupler to isolate the microcontroller and inverter. It important to properly work micro-controller in a noisy environment without unwanted resets and error running. Actually I am sure that this circuit reliable and I hope to match you want. If you have any doubts don’t hesitate to contact me. I am a new member to FreeLancer. So if has some problems with communication sorry for these. And I like to do this job for the minimum cost. Thank you.
₹600 INR за 1 день
0,0 (0 відгуки(-ів))
0,0
0,0
Аватарка користувача
I have experience to work at industry environment. I can finish the work in time . Let's go for work
₹1 050 INR за 2 дні(-в)
0,0 (0 відгуки(-ів))
0,0
0,0
Аватарка користувача
A proposal has not yet been provided
₹1 300 INR за 1 день
0,0 (0 відгуки(-ів))
0,0
0,0

Про клієнта

Прапор INDIA
Ghaziabad, India
5,0
1
Спосіб оплати верифіковано
На сайті з лист. 6, 2015

Верифікація клієнта

Дякуємо! Ми надіслали на вашу електронну пошту посилання для отримання безкоштовного кредиту.
Під час надсилання електронного листа сталася помилка. Будь ласка, спробуйте ще раз.
Зареєстрованих користувачів Загальна кількість опублікованих робіт
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Завантажуємо для перегляду
Дозвіл на визначення геолокації надано.
Ваш сеанс входу закінчився, і сеанс було закрито. Будь ласка, увійдіть знову.