Bandsaw automation

$250-750 USD

Закрито

Опублікований

almost 12 years ago

$250-750 USD

Оплачується при отриманні

Hi all, I need to automate the process where plastic tubes are cut to length, all hardware is forseen, we use an arduino uno with a phi LCD and keypad module. I need some code written to control this proces, in attach you can find more details about this project Regards, Bram

Arduino

ID проекту: 1603500

Про проект

7 пропозицій(-ї)

Дистанційний проект

Активність 12 yrs ago

Хочете заробити?

Переваги подання заявок на Freelancer

Вкажіть свій бюджет та терміни

Отримайте гроші за свою роботу

Опишіть свою пропозицію

Реєстрація та подання заявок у проекти є безкоштовними

7 фрілансерів(-и) готові виконати цю роботу у середньому за $472 USD

@MikroStar

hi, i can help

$730 USD за 24 дні(-в)

4,7

(3 відгуки(-ів))

5,5

@yhaat

Hello, I can do this job.

$500 USD за 15 дні(-в)

5,0

(20 відгуки(-ів))

4,9

@NishantSood5

I have worked on sophisticated projects in automation from programming ECU's to Automation, Please read my Message!

$325 USD за 8 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@ocengineer

I am an Electronic Engineer with 20+ years of experience developing automation solutions.

$350 USD за 17 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@RLT

Dear Sir, We are Reserach and Development company whose working area are : -Digital Motor Control -Analog Design -Electronic Design -Power Electronics -PCB design -Embedded system -Matlab -Simulation of hardware For each concept descriptions are as follows: Digital Motor Control: -3-phase induction motor vector control drive -Flux estimation algoritm generation -DSP(TMS320) implementation on motor drive -Low speed application -Torque and speed loop generation -Control algoritms Analog design -Low power distribution -Noissless special opamp based analog circuits -Analog filters -Orcad simulation of several circuits Electronic Design -RF transmitter and receiver -Bluetooh reader and transmitter -Magnetic reader Power Electronics -Implementation motor drive -AC/DC converter -DC-DC converter -Battery charger -Solar inverter -Renewable Energy simulations -Uninterruptle power supplies PCB design -Schematic design by Altium -PCB design by Altium -Power board design -SMPS board design Embedded system -PIC18,PIC24,PIC30 and dsPIC applications -Ardino -MSP430 -Atmel -DSP(Texas Instruments) -Renesas Matlab -Power Electronics simulation -Motor drive -Wind Energy -Solar Energy -Control applications Simulation of Hardware -Orcad Simulation(TI,National, Linear Tech, Maxim libraries) -LTI -National -Matlab Very important Note: References attached. Please look excel file to see projects which we made until now! Note: Payments will be funded as: 1)Initial:%25 2)Second stage:%15 3)Third stage:%20 4)Final stage:%40 Metin Akin

$500 USD за 10 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@RBlagoev

Hello, I'm an automation engineer more than 30 years. Please see my CV. My best regards

$500 USD за 20 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@amittriar

Hi Project Manager, I have good experience in Arduino programming. As per my understanding, I am hereby proposing my solution to the stated situation. I have an Arduino board already in my inventory. I can integrate it with PHI board stated and accordingly control the Bandsaw machine. Kindly elaborate it more. Regards; Amit

$275 USD за 10 дні(-в)