Find Jobs
Hire Freelancers

controlling a motor using labview

€30-250 EUR

Закрито
Опублікований about 5 years ago

€30-250 EUR

Оплачується при отриманні
Hi , Emma here , background semiconductor engineering . Project is a basic labview vi to control pressure in a vacuum chamber . Take a voltage reading in from a vacuum guage which represents a pressure reading , compare it to a setpoint pressure , and based on the result control a motor to throttle a butterfly valve on the pumping line until the incoming pressure matches the setpoint . The vacuum chamber will be pumping continuously and have a continous gas inlet to create the pressure . While the pressure reading can be captured through the Daq assistant , how can i setup the PID control of the motor to allow the butterfly valve throttle over and back to match the incoming pressure versus the setpoint , and hold it steady for couple minutes .
ID проекту: 18518899

Про проект

7 пропозицій(-ї)
Дистанційний проект
Активність 5 yrs ago

Хочете заробити?

Переваги подання заявок на Freelancer

Вкажіть свій бюджет та терміни
Отримайте гроші за свою роботу
Опишіть свою пропозицію
Реєстрація та подання заявок у проекти є безкоштовними
7 фрілансерів(-и) готові виконати цю роботу у середньому за €155 EUR
Аватарка користувача
Hello Emma, I would like to take this challenge. Can I have remote access via teamviewer to your computer where the system is running? Let me know if you willing to discuss details. We should agree also few milestones. Best regards, Nicolae
€200 EUR за 15 дні(-в)
4,9 (12 відгуки(-ів))
4,4
4,4
Аватарка користувача
Hi. I have good experience on LABView NXG, MyRio. I have done compressed natural gas machine project, and Automatic Human tracking on LabView related to your project. I have done list of other projects on Labview. Thanks
€160 EUR за 3 дні(-в)
0,0 (0 відгуки(-ів))
0,0
0,0
Аватарка користувача
Good experience working on simulations from the various software's, I would be delighted to work with you on this. thanks
€150 EUR за 3 дні(-в)
0,0 (0 відгуки(-ів))
0,0
0,0
Аватарка користувача
I have experience in development of LabView program with control via Ni-daqmx driver. First, check the stability of the closed system. Pid controller in LabView to create.
€248 EUR за 10 дні(-в)
0,0 (0 відгуки(-ів))
0,0
0,0
Аватарка користувача
Hi Emma! It is a fairly simple task. I am an CLAD certified Electrical Engineer with Masters in Controls. I can help you out in the development of your project. Please know, i have done sensor value acquisition using DAQ and then control of PID on the output motor using DAQ too. Looking forward to hearing from you soon. Regards.
€120 EUR за 5 дні(-в)
0,0 (0 відгуки(-ів))
0,0
0,0
Аватарка користувача
Its so easy i can do it for you. Iam a professional labVIEW programmer with alot of experience on control specially the Fuzzy and PID controls.. Hope to hear from you soon
€55 EUR за 2 дні(-в)
0,0 (0 відгуки(-ів))
0,0
0,0
Аватарка користувача
I am CLD certified professional having an experience of more than 7 years of experience in developing applications in Labview, money is not an issue for me I just want to start my first freelance prjt
€155 EUR за 3 дні(-в)
0,0 (0 відгуки(-ів))
0,0
0,0

Про клієнта

Прапор IRELAND
Dublin, Ireland
0,0
0
На сайті з січ. 13, 2019

Верифікація клієнта

Дякуємо! Ми надіслали на вашу електронну пошту посилання для отримання безкоштовного кредиту.
Під час надсилання електронного листа сталася помилка. Будь ласка, спробуйте ще раз.
Зареєстрованих користувачів Загальна кількість опублікованих робіт
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Завантажуємо для перегляду
Дозвіл на визначення геолокації надано.
Ваш сеанс входу закінчився, і сеанс було закрито. Будь ласка, увійдіть знову.