Design a 5v sun tracking unit on a 1"x2" max circuit board.

Виконано Опубліковано %project.relative_time Оплачується при отриманні

$30-250 USD

Оплачується при отриманні

Виконано Оплачується при отриманні

I am looking to build a miniature sun tracking device. This would be a two axis system utilizing 4 photo-resistors or if you have ideas of something different we can talk. The controller would have a 5volt input and be able to control 2 standard mini servos which run off of 5 volts. I would also like a timer function to conserve power. Preferably a 1 minute delay before moving sensors. This circuit would ideally fit on a board that is under 1x2 inches. The device would have a power and ground connector and 2 standard 3 prong servo connectors. The photo sensing aspect could be separate or ideally on the board as well. I am open for ideas and suggestions, the key is to keep it small and light weight.

Схемотехніка Електроніка Техніка Розводка друкованої плати Дизайн продукту

ID Проекту: #6230582

Про проект

12 заявок(-ки) Дистанційний проект Остання активність Jul 25, 2014

Хочете заробити?

Переваги подання заявок на Freelancer

Вкажіть свій бюджет та часові рамки
Отримайте плату за вашу роботу
Опишіть свою пропозицію
Реєстрація та подання заявок у проекти є безкоштовними

Доручено:

Світлина профілю chandra2sekhar
chandra2sekhar

Hello sir,I am [login to view URL] sekhar,[login to view URL],PhD. i have 10+ years experience in this field and i feel i can complete your task .right now the provided information is not [login to view URL] present bid & delivery time is just an app Більше

$370 USD за 10 дні(-в)
(41 відгуків(-и))
7.7

12 фрілансерів(-и) готові виконати цю роботу у середньому за $230

Світлина профілю tifoda
tifoda

Interesting project. Did same some time ago. What "standart servos" do you want to use? ----------

$166 USD за 14 дні(-в)
(20 відгуків(и))
5.1
Світлина профілю chamikaIGamage
chamikaIGamage

I'm Electronic engineer and I would like to use my extensive Embedded system design and PCB design knowledge to do this projects . I'm so experienced with Arduino, PIC ,DSpics and expert with orcad, proteus,Ni multisim Більше

$388 USD за 10 дні(-в)
(9 відгуків(и))
4.8
Світлина профілю eried
eried

Hey, this sounds fun :D What is the maximum height? And what precision do you expect? (in degrees? -- or in some imprecise US non SI unit? hhaha) Is consumption important? ----- Erwin

$222 USD за 30 дні(-в)
(20 відгуків(и))
4.7
Світлина профілю RKearmey
RKearmey

Well hey there! I have a few questions for you. Did you need this to use surface mount or through hole components? Are you locked onto a 1x2" board? What are the specs for the servos that you'd like to use? Woul Більше

$250 USD за 7 дні(-в)
(7 відгуків(и))
4.4
Світлина профілю ShaheerJaan
ShaheerJaan

A proposal has not yet been provided

$210 USD за 7 дні(-в)
(24 відгуків(и))
4.6
Світлина профілю sajith40
sajith40

i am a BE Electronics and communications candidate, and i have 5 years experience in design and embedded systems

$155 USD за 3 дні(-в)
(0 відгуків(и))
0.0
Світлина профілю pramodnatu
pramodnatu

I have worked in following areas for last 25 years • Pcb Artwork Layout: Mostly I do my pcb artwork layout in pads(Mentorgraphics). I am also familiar with Orcad ,Eagle,Altium. Right from my first job(back in 1984) Більше

$222 USD за 15 дні(-в)
(0 відгуків(и))
0.0
Опублікувати схожий проект