STM32 project

I have made few good projects on STM32 board and good exposure on it too. I am really interested in working with this tiny boy(stm32F103C8) . its all up to your vision.

Hi, I am a post graduate power electronics engineer and having very good experience in product design and development. I am excellent in embedded design & programming using pic, dspic controllers and MATLAB codding for Power projects, Boot loaders, Bluetooth & GPS designs, CAN communication, EEprom. UART , RF circuits ,Protocols for networking, wi-Fi routers,OBD diagnosis with CAN bus protocols, Electrical vehicles and AC drives, stepper motor controls. I designed sine wave inverters for standalone and grid tie Inverters. I designed projects like Off line UPS up to 3 KVA, 5kW motor controller for electrical vehicles ,synchronous rectifiers, Solar MPPT chargers, Solar trackers, Battery chargers ,Grid tie inverters design with PLL and feedback control circuit emergency light of 66W and Online UPS control cards, Battery Charging power supplies, LED drivers for PWM controlling and dimming, SMPS, Power supplies. I have experience in schematics and PCB design experience in Altium and ORCAD. I am ready to work for you. Please contact for further discussion.

I have done very complex projects with two UARTS, if you don't do it right you will have the following problem: 1. You will have blocking from UART2 to UART1 if you don't do this correctly 2. You will have a big mess with commands -> port execution if you don't do this correctly Send me more details, how many commands, what they need to do, and I can maybe lower my bid. If all of these things is not done in a non-blocking way, it will not work correctly. If you just send few bytes, and than wait, it will be OK, but if you need to support stream always comming (like for example telemetry, control, gaming, industry, etc.) you will have problems. Also, I have all hardware and software to test (bluepill for your processor, I usually use gcc, with Cross Studio for ARM), but that doesn't matter so much, any compiler is OK (Keil, IAR, I just prefer gcc for this type). I would use CubeMX, but the little tricks and details are what is expensive. I will send you version to flash before any payment. Even this price 100$ is very low, if you want to solve it 100% correct. Good luck!

Hello, I worked with many projects on multiple STM boards based on cubeMx. I used different IDEs such as system workbench, keil, and STMCubeIDE(I'll use STMCubeIDE as you wish). I have read the requirements, I did a similar project, and I believe that I can do this project. Contact me for more details.

Hello, I am an electornibcs and telecommunication engineer and I am quite experienced with embedded systems design. I have this microcontroller and I have done a couple of projects with it. I can help you with your project. Just give me all the details and I will do my best to help you. Best regards

Hi, I am Embedded Firmware Developer. I have good experience with embedded firmware development. let me know once you want to start the job. Thanks.

I have better knowledge in these topics

Hello dear client, you have specified that you want a professional mathematician coded it in Matlab. I CAN HANDLE THIS, MATLAB IS MY DAILY MEAL HIRE ME I START WORKING NOW THANKS

I am expert in stm32. i did lot projects on stm32, i can make very smart offer for you whenever your project is done you hire me also i can work both on arduino and keil mdk whatever you like

I am a embedded system Design engineer with expertise in hardware circuit design and stm32,arduino programming with sensors,timers, actuators and display menu config. I worked for startups also. I have background  of hardware  and pcb design also.  and I worked for several embedded  companies  as consultant  I will help you to do your work done with in a timelines and professionally. 

Hello India, im electronic ingenier and profesor. Actualy im working with the STM32 Bluepill SMT32F103C8 and the STM32CUBEIDE for CAN comunication. The proyect that you need is easy to do. I have 2 bluepill for make tests. If you want start to work in your proyect, tell me. Regards.

I am fresher to freelancer but not fresher to my programming career and also I done project with STM 32 , so I am ready to do this project.

I've working for 5 years on bluetooth communication with STM32f103c8t6. I created many projects like this

Hi, I have a good background in firmware development.i have 5+ years of experience in embedded development. I am currently working in a reputed robotic company. Your task seems interesting and we can develop the firmware easily and fast. I'm very flexible to work with and reliable.