Build a new firmware for my existing STM32 device

Dear Sir, I have used STM32 since 2012 and very familiar with both software and hardware side Of STM32. I have built lot of projects based on STM32, from Hobbyst to Military application. I'm familiar with UART,I2C,SPI,DMA,ADC,DAC, FSMC, and many more peripheral. Basically I'm firmware engineer, so I know how to manage Microcontroller especially STM32. I will use System Workbench as IDE, GCC-ARM-NONE-EABI as compiller, and STM32CUBEMX as project generator. This is my daily project. Let me know the details. Most of my recent project is related to IoT, so I'm not new with GPS, and your other requirements. let's discuss the detail over chat. let's get started. Best Regards, Rijal

Hi, I hope you are doing well. I have expertise in embedded system programming and development. I have reviewed your project details and would like to discuss it in more depth. Please send me message for further discussion. Looking Forward, Khawaja

Hi, I am a post graduate power electronics engineer and having very good experience in product design and development. I am excellent in embedded design & programming using pic, dspic controllers and MATLAB codding for Power projects, Boot loaders, Bluetooth & GPS designs, CAN communication, EEprom. UART , RF circuits ,Protocols for networking, wi-Fi routers,OBD diagnosis with CAN bus protocols, Electrical vehicles and AC drives, stepper motor controls. I designed sine wave inverters for standalone and grid tie Inverters. I designed projects like Off line UPS up to 3 KVA, 5kW motor controller for electrical vehicles ,synchronous rectifiers, Solar MPPT chargers, Solar trackers, Battery chargers ,Grid tie inverters design with PLL and feedback control circuit emergency light of 66W and Online UPS control cards, Battery Charging power supplies, LED drivers for PWM controlling and dimming, SMPS, Power supplies. I have experience in schematics and PCB design experience in Altium and ORCAD. I am ready to work for you. Please contact for further discussion.

Dear Sir, I am an expert with more than 15 years of experience in the field of embedded systems, electronics, prototyping and PCB Layouts. I have worked alot on developing ultra-low power applications using complex algorithms. I have checked the details of your project. I have the required discovery board (with STM32F103 on it) and IAR as well Keil IDE. I assure you the best solution for your work. Regards Ch

Hi, I would like to be considered for this project, i have vast experience of working on GPS,GSM and TCP/IP protocol.

I am Senior Embedded Systems & C/C++ developer. Developer expert on VC++, Eclipse Mars for C/C++, gcc,g++ in Win and Linux. OpenGL, OpenCV, Cuda. Developer expert on low level programing on C/C++. Expert on PIC, ATMEL, ARM Microcontroler and Arduino. Several years working with microcontrollers STM32F407 and STM32F103. STM32 HAL library.

Hi, I’m an experienced embedded systems developer with 4 years experience working on stm32 microcontrollers developing firmware for interfacing various devices in various applications, looking forward to working with you.

I hold master degree in instrument tech and having about 35 years of expertise in real time embedded hardware and software applications. I am well versed with GSM, GPS etc and have experience in SIM800, MC60 etc.

hello eir/madam i think i will be a good candidate to help you solve your problem. i have experience in building gps tracker using gsm via tcp protocol for bus tracking for universitas indonesia bus using stm32f108. if you are interested please chat me. thankyou regards, ghana n.

I have extensive experience of working on stm8s & stm32 device lineups so if you choose me over other I assure you get the work done as per your expectations. Thanks.

Hi. Thanks for your posting. I am an electronic engineer, having enough experience in IOT device, high speed circuit & PCB design. I am sure I can support you with my skills. Following is my skills and tools - Electrical & electronic diagram, and schematic & PCB design. • High circuit analysis and design such as DDR3, eMMC, 10Gbps Ethernet circuit • RF Antenna/Front end, filter. • Flexible PCB inlay design. design(Up to 12 layers PCB design). - Standardization and protocols • FCC, ISO/IEC 14443, ISO/IEC 18092, ISO 18000 • ISO IEC 7816, ISO/IEC 7815 - Firmware development for any MCU. • ARM Cortex Mxx, STM32xx, ATSAME70, AT91SAM, STC. • AVR: ATmega328, ATmega1280, ATmega2560, ATtiny43U, ATtiny85... • PIC: PIC16, 18, 24, 32 series • Raspberry Pi • Arduino series: arduino Uno, Mega2560 • Standalone RF module such as Nordic series, WiFi(ESP32, ESP8266) , BLE, Zigbee, Xbee Design Tools - Altium Designer 18, Cadsoft Eagle PADs, OrCAD - MPLAB X, Micro C, uKeil, STM32 workbench, AVR Studio. Arduino IDE - C, C++. I can give you a perfect project. Best Regards.

I had previously work with telematics Solutions based on IOT which is Vehicle Tracking System. Worked In Technology: 1. GPRS 2. GPS 3. Wifi 4. RTOS 5. FOTA 6. CAN 7. BLE 8. SPI 8. I2C 9. PCB Design 9. 32 bit Microcontroller 10. Raspberry Pi 11. Python 12. Arduino

I'm an electronic engineer with more than 15 years of work experience. I work as HW designer; FW and SW developer. As HW designer, I work in Altium, KiCad and Orcad and I have experience in development single MCU (Microchip PIC and ARM Cortex) boards with several digital I/O (GPIO, UART, SPI, I2C, PWM,....) and some analog I/O. I design complete board: power section, MCU section, peripheral section,.... I design also boards with battery power; so I have experience in low power PCB design. I have also experience in commercial boards (Arduino, Raspberry, Beaglebone,...) shields design. I have also experience in bluetooth (both 2.0 and 4.0) PCB design. As FW developer, usually I work in C for Microchip PIC (MPLAB X + XC compilers) and Eclipse + GNU ARM for different ARM Cortex M3/M4 manufacturers (STM32Fx, NXP, EFM32 SiLabs, but I'm ready to learn new frameworks). I work both single task and multi task environment (FreeRTOS and RTX). I write code both for low level driver (GPIO, UART, SPI, I2C, PWM....) management and for high level/final application. I work also in "C code" commercial boards Arduino/ESP8266 and Linux embedded commercial boards (Raspberry and Beaglebone). I have also experience in bluetooth (both 2.0 and 4.0) programming. As SW developer, I work in C, C++, .NET, Java, and lot of others programming languages. Mainly I work for Windows O.S., but I have experience in Linux development too. I have experience in openCV library for image/video processing. I have ex