Cisco To Juniper SRX QoS Configuration Translation

$30-250 AUD

Завершено

Опублікований

over 9 years ago

$30-250 AUD

Оплачується при отриманні

This should be a simple job for someone who has done the Junos configuration before. It should take no more than 2 hours, please bid accordingly. There is no router configuration required in this task. Just a simple document, similar to the attached will do, just for Junos. Please see the attached document of a Cisco configuration. I basically want it translated so I can run it on an SRX110 with 12.1X44-D40.2. I believe that the SRX110 has 8 queues on an interface, if that is going to be a limitation with my configuration, you can choose 8 of the classes to be included, once I see the example, I will be able to work it out the changes I require. I need an example of: i) a LAN interface policy to mark the traffic entering the router This is "policy-map BRANCH-LAN-EDGE-IN" in the attached document ii) a WAN interface policy to apply a bandwidth limit to the overall interface This is "policy-map BRANCH-WAN-EDGE" in the attached document iIi) a sub policy that runs under the WAN interface policy to split the bandwidth into separate categories. This needs to cover the instances where the interface throughput is much lower than the interface capability. EG 20M metro ethernet service. Is this any difference for ADSL or 3G interfaces? This can be seen as "policy-map 4M" in the attached document I will also need the code fragment for how to attach the QoS policies to both ethernet, ADSL and 3G backup interfaces. All this needs to be is the equivalent of int g0/1 service-policy output 4M I will need the commands to verify that the qos policy has been applied and to show the relevant statistics. The equivalent of: show policy-map int g0/1

Cisco

Network Administration

ID проекту: 6711720

Про проект

8 пропозицій(-ї)

Дистанційний проект

Активність 9 yrs ago

Хочете заробити?

Переваги подання заявок на Freelancer

Вкажіть свій бюджет та терміни

Отримайте гроші за свою роботу

Опишіть свою пропозицію

Реєстрація та подання заявок у проекти є безкоштовними

Доручений:

@loveengupta

Configuring QOS on daily basis on service provider domian, i will give you watever u want, just my inception in free lancing, give me a try. i m pasting the sample steps to do , if u like please let me 1)defining policy for shaper as per juniper standard set firewall policer <Bandwidth>-policing filter-specific set firewall policer <Bandwidth>-policing logical-interface-policer set firewall policer <Bandwidth>-policing if-exceeding bandwidth-limit <Bandwidth> set firewall policer <Bandwidth>-policing if-exceeding burst-size-limit <Burst-buffer> (you can decide or we can discuss as per the standfards) set firewall policer <Bandwidth>-policing then discard 2)defining parent policy set firewall filter 4M filter interface-specific set firewall filter 4M filter term Parent-policer then policer <Bandwidth>-policing set firewall filter 4M filter term Parent-policer then next term 3)filter creation as per the priority(like policy map matching class) set firewall filter 4M filter term vedio from dscp ef bit matching set firewall filter 4M filter term vedio then policer <percent>-policing bandwidth which will be applied to the class set firewall filter 4M filter term vedio then loss-priority low set firewall filter 4M filter term vedio then forwarding-class Premium - name of the class set firewall filter 4M filter term vedio then accept 4)corresspondingly all bits are difined in sequence 5)set interfaces <name> family inet filter input 4M filter (calling filter on interface

$45 AUD за 1 день

4,6

(17 відгуки(-ів))

4,3

8 фрілансерів(-и) готові виконати цю роботу у середньому за $159 AUD

@frugees

Good day, I am ready to do this. Hire me and i shall start. This a task i can complete, my experience permits me to do this without any issues. Sincerely

$200 AUD за 3 дні(-в)

5,0

(191 відгуки(-ів))

6,9

@mandeepsingh0617

Greetings of the day, i have read your requirements and Cisco Configuration also, as we discussed in the morning we can start the configuration. Thank you

$200 AUD за 3 дні(-в)

4,9

(19 відгуки(-ів))

4,3

@tanthanh2285

This is Andy. I'm mastering on Cisco router, my friend mastering on Juniper products. We both will work for this bid.

$250 AUD за 3 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@tosatish

I am Senior QA Engineer with more than 6 years of experience. having masters in computer network engineering. worked for JUNIPER NETWORKS, TELLABS, SPIRENT, BARRACUDA NETWORKS on Security and Routing Products. I have worked for Juniper Networks India Pvt Ltd for 3+ years on features like QOS, Firewall. I can help you in this job. I worked in security business unit on SRX series routers. I have worked on all series of SRX routers. I have configured and tested QOS features on JUNOS. Worked on various releases starting from 10.0, 10.1, 10.2, 10.3, 10.4, 11.1, 11,2,11.3 and 11.4. Experience in testing of routers and firewalls, which include functional, testing of class of service and QOS, related testing with respect to Product Limitations. Testing includes: Class of service, firewall, Filters, Policer, QOS, DHCP relay, IPv4 stack I think I can do this job. budget is not major concern, we can discuss and negotiate on it to make it feasible for both of us. Thanks, Satish

$222 AUD за 3 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@ify9star

I have more than 5 years experience with networking technologies i.e Cisco, Juniper, Alcatel, Linux I already have the juniper version of the configurations. Contact me to discuss.

$90 AUD за 1 день

0,0

(0 відгуки(-ів))

0,0

@vijaykris80

CCIE with 10+ years experience in Network Industry. Have relevant experience in Juniper as well. Thanks Vijay

$222 AUD за 3 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@ispooster

I have worked as a Juniper TAC engineer for over a year and as a Cisco TAC engineer for 3 years. I can easily do this job. The only reason I am bidding low is to make some reputation here.

$45 AUD за 3 дні(-в)