Electronic circuit design - PCB design - circuit built

$250-750 AUD

Закрито

Опублікований

about 5 years ago

$250-750 AUD

Оплачується при отриманні

We need a person with electronic circuit design skills that can also design the PCB and do the final circuit assembly. The circuit would be based around the Sensitec sensor AFF756. We would need to be able to have an analogue output signal from the sensor that can be recorded with a standard data acquisition card. There will be a few external components to provide flip coil current (HKB from IC-Haus), an analogue amplifier chip (LT1028) and probably a frequency generator. Details of the circuit can be found in the datasheet of Sensitec AFF755B sensor (Fig. 8, 9) and we will also be discussing this via phone/Skype to ensure the circuit will meet our requirements. We expect this project to take about 8 h.

Electronic Design

PCB Design and Layout

ID проекту: 18886220

Про проект

9 пропозицій(-ї)

Дистанційний проект

Активність 5 yrs ago

Хочете заробити?

Переваги подання заявок на Freelancer

Вкажіть свій бюджет та терміни

Отримайте гроші за свою роботу

Опишіть свою пропозицію

Реєстрація та подання заявок у проекти є безкоштовними

9 фрілансерів(-и) готові виконати цю роботу у середньому за $520 AUD

@mairajali11

Hello I am an Electrical Engineer did MS in Electrical Engineering (Control System) as well. I have 4 years of Experience as well, also have 11 IEEE conference publications and 3 Journals with good impact factor. My major Expertise are: - MATLAB, SIMULINK modelling and simulation in Electrical and Electronics Engineering. - AutoCAD, Multisim, Labview, Eagle, Proteus, C/C++, Circuit designing, Engineering Mathematics and other Electrical Engineering subjects. - Plagiarism removal, Research paper writing, Academic writing, Technical Writing. - VHDL/Verilog HDL, Xilinx, and FPGA. - PCB Desigining - Data Entry, Ms. Office, PDF conversion, pdf editing, copy typing etc. inbox me to discuss it further.

$250 AUD за 1 день

5,0

(1 відгук)

2,0

@Tomorrow1201

Hi there. I offer you the services for PCB designs/assembly. I just completed one job in PCB. I am new on freelancer site, but I am designer expert with 10+ years of experience in Circuit designs, PCB designs, Zigbee/bluetooth,Wifi software development. You can check our designs in our portfolio. If you want, I will share more designs I completed so far through interview. So I like to discuss the job with you. Lets talk about your project through interview. Thank you.

$400 AUD за 5 дні(-в)

1,0

(2 відгуки(-ів))

3,2

@ritz94

I am a professional Electrical engineer and also knowledgeable in electronic circuit design & pcb control device..I can design any kind of circuit board and pcb. I assured that me and my team done this job with in 3 days.

$388 AUD за 3 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@rajeeviitd

Experienced embedded system developer worked at Indian Institute of Technology, Delhi. Having more than four years experience in the vertical.

$722 AUD за 7 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@Zubair01S

Dear Sir , My Biography is written in my profile , i am working under the projects of fabrication lab (fab lab) and in this room , i only spent my time and energy in making PCBs of different controllers and RF Printed circuit board of high quality , high speed and low noise analogue so i have broad experience of designing circuit and PCBs. I am good PCB Physical Lead design engineer , so you can believe in my skills and give me at-least one chance. Waiting for your response. Regards Zubair soomro Electronic engineer

$555 AUD за 10 дні(-в)