Arduino Promgramming Gyro/Controlling Servo

$30-250 CAD

Закрито

Опублікований

over 11 years ago

$30-250 CAD

Оплачується при отриманні

Hi there, I am looking to develop a small project and i need someone to help me with initial programming. I believe this will be a few cycles on development before it gets to be perfect. I would like someone with good engligh skills and a phone number to be able to connect on the phone. A signed NDA will need to be part of this before more details are released but the general concept is as follows. Hardware. Arduino Servo (model to be determined later) Gyro (IDG500) Accellerometer Kalman filter applied to keep accurate Software spec. Gyro/Accelerometer will be on a fixed point that Rotates on the X axis Servo will be connected to the fixed point, the the motor will turn in perfect relation to the movement on the X axis (to keep level) Please email me if you are interested in this project.

Arduino

C Programming

ID проекту: 2481780

Про проект

9 пропозицій(-ї)

Дистанційний проект

Активність 12 yrs ago

Хочете заробити?

Переваги подання заявок на Freelancer

Вкажіть свій бюджет та терміни

Отримайте гроші за свою роботу

Опишіть свою пропозицію

Реєстрація та подання заявок у проекти є безкоштовними

9 фрілансерів(-и) готові виконати цю роботу у середньому за $194 CAD

@yhaat

Hi, I can do this job.

$250 CAD за 10 дні(-в)

5,0

(17 відгуки(-ів))

4,8

@argento

Hi, please check PMB to discuss project scope. Thanks.

$250 CAD за 15 дні(-в)

5,0

(16 відгуки(-ів))

4,5

@FieldingBlue

Thankyou for the invitation to submit a proposal. I am a computer systems engineer and electronics technician. I have 10 years experience as a technican on aircraft and simulators to component level. I also have ten years experience as an engineer working on software, hardware and sensor systems. I recently completed a project for an emebedded system to interface a robotics controller to a GPS tracking system on heavy vehicles. The 30 units produced have been working reliably and without failure, for the last 8 months Amongst others, I have also performed code review and enhancement of firmware on an aircraft environmental monitoring unit and a video switch matrix. I am happy to discuss changes to requirements and scope should these change during the course of the work. Regards FieldingBlue

$250 CAD за 30 дні(-в)

5,0

(1 відгук)

4,0

@nevamalap

Hello, I am interested in your project. Please contact me. Thank you.

$150 CAD за 10 дні(-в)

5,0

(1 відгук)

2,0

@vishalgaurav88

can i help you

$150 CAD за 9 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@betaenergy

Dear Sir, I have 10 year experience on analog design, audio system, power electronics, digital motor control, inverters, converters, DC-DC converters, power distribution sysetms, PCB design, circuit simulation, system simulation. The document which shows my background is attached. It shows my ability to make your work. I have gratuated Hacettepe University electric and Electronics engineer. I have passed several courses until now. My university is one of 500 th university in the world. To discuss details of project, you can ask me any questions. By talking we can agree on terms and conditions of your Project. I hope you will give oppurtinutiy to show my intelligence and reasoning. Regards. Beta

$220 CAD за 5 дні(-в)

0,0

(2 відгуки(-ів))

0,0

@Jl2o5MJ9O

Custom software development (<b><i>Removed by Admin</i></b>)

$250 CAD за 1 день

0,0

(0 відгуки(-ів))

0,0

@shashraf

Hello, I have implemented a full orientation tracking system before using a 9DOF stick containing a 3-axis magnetometer, 3-axis gyroscope and a 3-axis accelerometer. You can see my portfolio. Please check PM for more details.

$200 CAD за 4 дні(-в)