Create a Zigbee router, using the cc2530 module.

$100-500 USD

В роботі

Опублікований

about 3 years ago

$100-500 USD

Оплачується при отриманні

For increasing the range of my ZigBee devices, i would like an firmware, built for the DL-22 module (CC2530+CC2591) so it will act like an ZigBee router. My Coordinator should be able to find the new router, through scanning after the EUI (Like when pairing a regular ZigBee device). In general, the functionality of a regular smartplugs router capabilities, inserted into the DL-22 module. This is a software based project, no modifications should be done to the physical module itself. Requirements: - The firmware is built for the DL-22 module - The finished router has a EUI (preferably an EUI we can choose ourselves, during the firmware install process). - Either using ZigBee 3.0 or ZigBee SE. - An coordinator should be able to pair multiple routers.

Electronics

Zigbee

Firmware

ID проекту: 29377436

Про проект

3 пропозицій(-ї)

Дистанційний проект

Активність 3 yrs ago

Хочете заробити?

Переваги подання заявок на Freelancer

Вкажіть свій бюджет та терміни

Отримайте гроші за свою роботу

Опишіть свою пропозицію

Реєстрація та подання заявок у проекти є безкоштовними

Доручений:

@omoboladeolumode

Hello sir/ma, I'm interested in taking this task up for you, i can Create a Zigbee router, using the cc2530 module. I am an Electrical Engineer with a masters degree and I have high proficiency knowledge in: FPGA firmware in VHDL and Verilog for Altera/Actel/Xilinx FPGAs and EEG signal, MCU firmware in C/C++ for ARM, TI, NXP, Atmel, PIC, Arduino; Bluetooth, Raspberry Pi, OpenCV, Deep Learning, Bluetooth Low Energy (BLE), and wireless modules programming,, GPS modules, Temperature, Pressure sensors, Metal Detectors, motor drivers, 12V, 24V DC motors, Schematic, PCB Layout: Altium Designer, Component selection, BOM generation, Gerber generation, HVAC, LTE system model, Thermal system design, Matlab/ Simulink, Microcontroller, Modeling, optimization, simulation of building energy systems, and have been working on Industrial Automatics, Prototyping, PCB Design, Development of Electronic systems. Once you share the project, I will have a look & confirm if I can do it. I’m honest, creative and a unique person to carry out your tasks given to me. Leaving your project on our hand is privileged; we'll make sure that the project is done in a perfect way and do our best until you were satisfied. I would love to discuss this project with you and meet your exact requirements. I am confident I can provide you with top-notch materials that will fit your needs. I pride my work on being professional, of the highest quality and always delivered on time.

$100 USD за 2 дні(-в)

0,0

(0 відгуки(-ів))

0,0

3 фрілансерів(-и) готові виконати цю роботу у середньому за $292 USD

@hayat38402

We are a team of Electrical and Electronics engineers having Excellence in the following areas: • Embedded C Programming. • VHDL/Verilog, LABView/ Multisim/PSPICE • Network Simulator NS2/3 • Microcontroller like Arduino, Raspberry Pi, FPGA, AVR, PIC and STM32. • IDEs like Keil MDK V5, ATmel studio and MPLab XC8. • PLCs / SCADA • PCB Designing-Proteus, Eagle. • IOT Technologies like Ethernet, GSM GPRS. • HTTP Restful APIs connection for IOT Communications. Also we have good command over report writing, I can show you many samples of our previous reports. Kindly consider us for your project and text me so that we can further discuss specifically about your project's main goals and requirements. We can deliver your project efficiently within timeline. If you choose me, I think you won't regret. Best Regards.

$500 USD за 7 дні(-в)