ANSYS Heat Applications

$30-250 USD

Закрито

Опублікований

over 10 years ago

$30-250 USD

Оплачується при отриманні

1- Create a finite element model for one of the fin geometry shown in figure. Try to use the parametric modeling feature in ANSYS so that it will be easy to change the model for different dimensions L and t. Assume a constant temperature on the inner surface of the base surface and solve the steady state heat transfer problem and find the heat transferred with and without the fin. Change dimensions, repeat above calculations and plot the heat transfer improvement ratio a) Assume appropriate numerical values for geometry, outer temperature, material properties and boundary conditions and solve the problem using Ansys or Matlab with appropriate two-dimensional solid elements. Utilize symmetry to minimize the model size. b) Calculate the heat flux at the wall (x=0) analytically and using Ansys or Matlab. c) Compare solutions and comment.

Mechanical Engineering

ID проекту: 5399462

Про проект

12 пропозицій(-ї)

Дистанційний проект

Активність 10 yrs ago

Хочете заробити?

Переваги подання заявок на Freelancer

Вкажіть свій бюджет та терміни

Отримайте гроші за свою роботу

Опишіть свою пропозицію

Реєстрація та подання заявок у проекти є безкоштовними

12 фрілансерів(-и) готові виконати цю роботу у середньому за $147 USD

@ranscfd

• Strong Computer Aided Engineering Analysis experience in FEA and CFD • 8+ years of experience in FEA and CFD analysis of Automotive, Turbomachinery and Nuclear components using ANSYS platform. • Experience in ANSYS FSI, Structural and Thermal Analysis • Experience in steady &unsteady aerodynamics of axial compressor, turbine stage and marine propeller using CFX/Fluent

$189 USD за 5 дні(-в)

4,5

(15 відгуки(-ів))

5,4

@vviswanathan88

Hi, We are ANSYS exeprts. We can do this project and deliver on time. Some of the projects we did using ANSYS are as follows: Analysis of clutch housing of an automotive. Design and Analysis of lifting cradle for transporting heavy equipment. Modal analyses of pressure switch in a pipeline. CFD analysis of rotating blades of movers. CFD analysis of an inlet manifold. Fatigue analysis of a knuckle of a passenger car. Stress analysis of a heavy-duty tire-manufacturing machine. Aero dynamics analysis of an automobile. PSD analysis of bicycles carrier in an automotive. Meshing of a plastic flow analysis. Airflow analysis of air conditioner duct in an automobile. Parametric modeling and analysis for structural optimization of washing machine tub. Simulation of a quenching process using Finite elements analysis. BIW pre processing for crash analysis of automobile. Drop test of container. Stress analysis of bulk carriers. Analysis of headers in heat exchangers. Analysis of seat frame of passenger. Transient thermal analysis of ceramic process simulation. Shock analysis of on board structures. Structural analysis of impellers. Analysis of storage tanks. Thanks and regards, V. Vishnuvardan

$250 USD за 5 дні(-в)

4,8

(7 відгуки(-ів))

3,6

@mariannedelcu

Phd In physics. Large experience in research and complex phenomena using matlab. I will be glad to help you. Please send a message back to establish the details.

$150 USD за 3 дні(-в)

5,0

(7 відгуки(-ів))

3,4

@ChrisOchy

who could better do your task than a mechanical engineer with 4 years work experience. I can effectively complete the task

$155 USD за 3 дні(-в)

4,7

(2 відгуки(-ів))

1,3

@gyorgytoth

25 years experience in the use of Finite element systems like Nastran, Abaqus, Fluent, Ansys or Radioss. Several heat transfer problem solved already in different softwares. Good knowledge of Matlab and Hypermesh

$222 USD за 5 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@marcocardilli

Hello, i use ansys 15.0, and i'm thermal engineer since 2002. I work in avionics industry, and i've the highest skills in thermal and structural design of all on board equipment. I think that 3 days for the job can be enough, but we can talk each other to better define your needs. Regards.

$155 USD за 3 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@kurianpapps

My thesis work is on forming of plates due to moving heat source. I am confident to finish this work on time because for the last 2.5 years I was working on a similar kind of project even though I am unable to see the said figure yet. I am comfortable to work with Ansys APDL, fortunately we have access to Ansys in our department. We are also allowed to undertake such projects as they will finally help us to gain experience and which will have a positive reflection on our research work.

$166 USD за 2 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@rajeraviraj00697

A proposal has not yet been provided

$111 USD за 3 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@arminvwsa

Hi. My name is Armin. Watch my profile. I am good in Catia, Cad, Ansys, Simulink, Matlab, SolidWorks. This is a project for me. I will do it for minimum price. Regards

$155 USD за 3 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@PanayotPaskov

Experience in parametric design with ANSYS Workbench. Experience in heat exchange of the huge excahangers in thermal power engineering and domestic heating.

$155 USD за 3 дні(-в)

0,0

(0 відгуки(-ів))

0,0

@varung2610

I am doing job in a service company which provides services to a French company Alstom. ALstom has a very good name in wind turbine manufacturing. I carry out the mechanical analysis of structures and components of these wind turbine using the software ANSYS workbench and APDL. I have been using this software since a year and have become proficient in it. I can assure you that if am given the geometry, i can finish up this problem in one day. If needed I can work on a apdl macro which will make your task very easy. I am a graduate from the best college in India so you can definitely trust my analytically and qunatative ability, however am very new to this site so I donot have any reputations points to show off. I hope you give me a chance to prove it to you. Thanks

$50 USD за 3 дні(-в)